Opening a project
Use File › Open project (Ctrl+O), pick one from File › Recent projects or the start window, or drag a project file onto the window. The viewer opens:
| File | What it is |
|---|---|
.zw1 | A packed EPLAN project (the archive EPLAN makes with Project › Organize › Back up). |
.elk / .edb | An EPLAN project in its own folder, as EPLAN keeps it. |
With a project open, the title bar shows the project's name first: 26-0266 - ZW1 Viewer 26.10.05. File › Close project (Ctrl+W) closes it and shows the start window to load another one.
Opening from Windows Explorer
File › Show in Windows "Open with" adds ZW1 Viewer to the right-click menu Open with of
.zw1, .elk, .elp and .els files (for your Windows user only, no
administrator rights needed). Click it again to remove it. To open these files with a double click, choose
Open with › Choose another app › ZW1 Viewer and tick Always: Windows leaves that choice to you.
When ZW1 Viewer is moved to another folder, the entry follows it the next time the program starts.
A project opened from Explorer goes to a ZW1 Viewer that is already running without a project (the start window closes for it); when every open window has a project, it opens in a new window, so a project you are looking at is never replaced.
Packed projects (.zw1)
A .zw1 is unpacked into a folder next to it, named after it with _zw1viewer added
(Machine.zw1 → Machine_zw1viewer). That folder is kept: the next time the same file opens
at once, without unpacking. When the .zw1 changes it is unpacked again. You may delete the folder at any
time. When nothing can be written next to the file (a read-only share, a CD), the viewer unpacks into its own
Temp folder and removes it again when the project closes.
Projects that EPLAN has open
While EPLAN has a project open, some of its files are in use and EPLAN puts lock files (*.lck) among them.
The viewer notices this and reads a copy of the project, taken at the moment you open it, the same way a copy made in
Explorer still opens. You see "The project is open in another program (EPLAN): reading a copy..." while it copies.
The copy lies in the viewer's Temp folder and is removed when the project closes. Changes made in EPLAN
afterwards are not seen until you open the project again.
Recent projects
The viewer remembers every project you open, when you last opened it, the last page you looked at and its page filter, and comes back to them. When the project changed since then, it asks whether to set the filter again. File › Recent projects lists the pinned projects (with a pin) and below them the 10 projects opened last; the start window lists them all. Clear list keeps the pinned ones.
The start window
When the program starts without a project, and after File › Close project, the start window opens; you can also open it with File › Start window.
- Open recent: every project opened before, grouped by when it was last opened: Pinned, Today, Yesterday, This week, This month, Older. Each line shows the file name, its folder and the date it was last opened. A project whose file is gone shows in red, (not found).
- A click on a project opens it. With the keyboard: the arrow keys and Enter; typing goes to the search box.
- Search: type part of the name or the folder.
- Pin: the pin at the right of a line (shown when the mouse is over it) pins the project to the top; a pinned project always shows a filled pin, and clicking it again unpins it. Pinned projects never drop off the list.
- Right click: Open, Pin / Unpin, Remove from list (Del), Copy path, Open containing folder.
- Open a project... shows the open dialog; Continue without a project (or Esc) closes the window; Close program closes the viewer.
- Show this window when the program starts: untick it to start without the window.
The Pages tab
The pages of the project in EPLAN's page structure. Click a page to show it.
- Filters above the tree (
=function,+location,&document): show only the pages of that part of the structure. No filter shows them all. - Check boxes: check the pages you want to print or export. Checking a structure node checks every page under it. Without checked pages, printing and exporting use the selected page or structure node.
- PgUp / PgDn in the page view go to the previous / next page in the tree.
The page view
- Zoom with the mouse wheel, towards the mouse pointer. Pan by dragging with the left or middle button.
- Zoom to fit: F5 or double click.
- Links: cross references, interruption points and contact images are links: the pointer changes over them, a click jumps to the other page and the target flashes.
- Back / Forward: Alt+← / Alt+→, or the back and forward buttons of the mouse.
- Measuring: right click › Measure or M, then click two points. A point snaps to the end or middle of a line, a corner, or the centre of a circle or arc when one is near the mouse. You get the length and its X and Y parts. On a page drawn at a scale (a 2D layout at 1:9) and in a model view (1:6.67) the length is the real one, with the scale and the length on paper below it. Esc clears the measurement, a second Esc (or M) ends measuring. A measurement is not printed or exported.
- The status bar shows the page, its number of objects and, when something on the page is not drawn yet, "not yet drawn: ...". That is useful to mention in a problem report.
The symbol panel
View › Symbol panel (F4). Click a symbol on a page, or a part in the 3D view or its tree, and the panel shows its device tag, its function text, its articles and where its main symbol is. For a wire: its length and its routing path. Texts in the panel can be copied.
The Layout tab (3D)
The cabinet layout of the project in 3D, when the project has one. The tree on the left is read when the project opens; the 3D view is only drawn the first time you open the tab, fitted into the window. It is drawn by the graphics card (OpenGL).
- Mouse: left drag rotates, right drag pans, the wheel zooms, a right click opens the menu.
- Keys: F or F5 zoom to fit; 1 front, 3 side, 7 top, 9 back, 0 the default oblique view; the arrow keys rotate; M measure; Esc clears the selection.
- Click a part to select it (the symbol panel shows it). Double click a part, in the view or the tree, to go to its page; Alt+← brings you back to the 3D view.
- Doors: right click a door to open it to 90°, 120°, as far as it goes, or to close it; the menu also opens and closes all doors at once. Everything mounted on the door turns with it, and so do the wires on it: they leave the door at the hinge and run on into the cabinet.
- Wire ducts show their fill: the percentage EPLAN calculated when it is filled in, else the viewer's own figure from the routed wires.
- View › 3D transparency and View › 3D edges switch see-through housings and outlines.
The tree
- Layout spaces with their enclosures, mounting panels, ducts, rails and parts, each with its own icon. Uncheck a part or a group to hide it, with everything in it.
- Housing parts are named by their place: roof, rear panel, bottom panel, side panels, doors.
- Terminal strips: the terminals of a strip are under a node with the strip's name (X20), each named by its terminal number (1, 2, PE), in the order they sit on the rail, with the end stops and end covers where they sit.
- Restricted areas, holes and routing paths: when a part has more than one of a kind, they are under a node of their own, Restricted placing area (632). These are hidden at first: tick the node to show them. Holes show their size: Threaded hole, M5, Drill hole, Ø 11,5 mm.
- Routed wires and curves are under the enclosure they lie in, so hiding the enclosure hides them too. Wires between two enclosures stay in the layout space.
Wires
- A routed wire is a tube as thick as its cross-section (or its article's outer diameter), in the colours of its colour code; a wire of two or more colours shows them as stripes round it.
- A wire without a cross-section is a hair wire: a thin line, light blue unless it has a colour code.
Cables and wires that are not routed in EPLAN are not drawn: the viewer does not guess their path.
Measuring in 3D
Right click › Measure or M in the 3D view. The pointer becomes a cross and a click picks a point instead of a part:
- A point snaps to a corner (a filled square) or to the centre of a hole or round edge (a circle with a cross) when one is near the mouse; elsewhere it is the point on the surface (an open square).
- The first click fixes the first point; a line follows the mouse. The second click fixes the measurement: the length, and the distances along X, Y and Z (ΔX, ΔY, ΔZ). A third click starts a new one.
- Turning, panning and zooming still work while measuring.
- Esc clears the measurement; a second Esc (or M) ends measuring.
Printing
File › Print selected pages (Ctrl+P) and File › Print preview print the checked pages, or the selected page or structure node when nothing is checked.
Exporting
All exports take the same pages as printing. The viewer remembers the last folder per kind of export.
| Menu | Result |
|---|---|
| Export to image (PNG, JPG, TIF) | One picture per page at 200 dpi. |
| Export to DXF | One DXF drawing per page, for CAD programs. |
| Export to PDF (bookmarks, links) | One PDF with a bookmark per page, the cross references as links, and like EPLAN's own PDFs: a click on a device jumps to its line in the parts list, a click on a device tag in the parts list jumps back to the page where the device is. |
| Export to PDF (drawings only) | One PDF with just the pages. |
A PDF is written in the background: the program stays usable and the status bar shows the progress. Closing the project cancels it.
The View menu
- Zoom fit (F5), Back (Alt+←), Forward (Alt+→).
- Symbol panel (F4).
- Project language, Program language: see below.
- 3D transparency, 3D edges: for the Layout tab.
Languages
- Program language (View menu): the language of the viewer's menus and messages.
- Project language (View menu, only with a project open): the language the project's multi-language texts are shown in. Project default is the language the project shows in EPLAN; below it are the project's own languages (its translation languages). Every project starts in its default language. Switching keeps the page or 3D view you are looking at.
Reporting a problem
Help › Report a problem sends a report to the author of ZW1 Viewer. Open the page that is drawn wrong first: the report can take that page along. For a problem in the 3D view, tick Help › Detailed log first and repeat what went wrong: the log that goes with the report then holds the details.
- Describe what is wrong: what you did, what you expected and what the viewer did.
- Your e-mail address is optional. Fill it in if you want an answer; leave it empty to stay anonymous.
- Choose what goes along:
- The program's log of this session: with your user name, computer name and folder names taken out.
- The data of the page shown: the objects of the page with every text masked (
-F6becomes-X9,MotorbecomesXxxxx), plus what the viewer could not draw and the errors it met. This is usually enough to find the cause. - A picture of the page: off unless you tick it, because the page's texts can be read on it.
- The real names of the project and the page: off unless you tick it; otherwise a code is sent.
- Show what is sent shows the complete report before anything leaves your computer.
- Send sends it over an encrypted connection (HTTPS); you get the report's number. Or Save to file and mail the file yourself.
Privacy
- Nothing is sent until you press Send.
- The website does not store your IP address. It only counts reports per sender (through a one-way code) to stop floods.
- The report carries a random installation number made on your computer, so several reports from one installation can be seen together. It says nothing about you or your computer.
- Reports are only used to fix the viewer and are not passed on.
Keys and mouse
| Where | Key / mouse | Does |
|---|---|---|
| Everywhere | Ctrl+O | Open a project |
| Ctrl+W | Close the project (and show the start window) | |
| Ctrl+P | Print the selected pages | |
| F1 | This help | |
| F4 | Symbol panel on / off | |
| Alt+← / → | Back / forward | |
| Start window | Click, Enter | Open the project |
| Typing | Search | |
| Del | Remove from the list | |
| Esc | Continue without a project | |
| Page view | Wheel | Zoom |
| Left or middle drag | Pan | |
| Click | Follow a link, or select a symbol | |
| Double click, F5 | Zoom to fit | |
| PgUp / PgDn | Previous / next page | |
| Mouse back / forward buttons | Back / forward | |
| Right click | Menu (measure, zoom to fit) | |
| M, Esc | Measure on / off, clear the measurement | |
| 3D view | Left drag | Rotate |
| Right drag | Pan | |
| Wheel | Zoom | |
| Right click | Menu (views, doors, transparency, edges, measure) | |
| Double click | On a part: its page; on empty space: zoom to fit | |
| F, F5 | Zoom to fit | |
| 1 3 7 9 0 | Front, side, top, back, oblique | |
| Arrow keys | Rotate | |
| M | Measure on / off | |
| Esc | Clear the measurement, end measuring, or clear the selection |
Files the viewer makes
| Where | What |
|---|---|
<project>_zw1viewer next to a .zw1 | The unpacked project, kept for the next open. May be deleted. |
Temp next to the program | Copies of projects EPLAN has open, and unpacked projects that could not go next to their file. Removed on close, or at the next start. |
Logs next to the program | One log file per day. |
ZW1Viewer.config.json next to the program | The settings: recent projects (with their dates and pins), export folders, languages, the menu ticks and whether the start window shows. |
The viewer never changes the project itself.